Stove and oven faults don't always announce themselves clearly.
A gas burner that ignites on the third click instead of the first. An oven that reaches temperature eventually but takes longer than it should. A glass cooktop with a surface fault that you're not sure is cosmetic or structural.
In Winter Park, Refrigerator Service Center handles all of it — gas and electric, stoves and ovens, all major brands — with the same diagnostic rigour applied to every appliance we service. We identify the fault, explain the cause, and verify the repair before leaving.
Stove and Oven Faults We Fix in Winter Park — And What Each Typically Involves
Gas Stove Repair
Spark module testing, igniter switch assessment, gas valve inspection, and burner port evaluation. Intermittent ignition and complete ignition failure have different causes and each is tested in sequence.
Electric Stove Repair
Burner element testing, infinite switch diagnostics, and control board assessment. We stock heating elements for the most common residential configurations.
Gas Oven Repair in Winter Park
Igniter glow bar assessment, gas valve testing, safety valve inspection, and thermostat calibration. Every gas oven job includes a confirmed heat cycle with temperature verification before closing.
Electric Oven Repair
Bake and broil element testing, cycling thermostat assessment, door seal inspection, and control board diagnostics. Temperature confirmed with a reference thermometer on every oven repair visit.
Glass Cooktop Repair & Replacement
Surface crack assessment, subsurface element testing, and full panel replacement. We evaluate structural integrity before recommending replacement.
Stove and Oven Installation
Gas line confirmation, electrical connection verification, anti-tip bracket fitting, levelling, and full operational testing before handover.
Three Reasons Homeowners in Winter Park Don't Book — Answered Honestly
Price Uncertainty
The diagnostic visit gives you a clear, specific price before any work begins. No surprises. No commitment required.
The Age Question
"The stove is eight years old — is it worth fixing?" We give you an honest comparison. Often, repairing a quality appliance is far more economical than replacement.
Trust Concerns
We document every test and repair. If the same fault returns, we have a complete record to resolve it correctly this time.
What the Stove or Oven Looks Like After an RSC Visit
When a stove or oven repair is complete at Refrigerator Service Center, it means: the primary fault was identified through testing, not assumption. The component was replaced and verified to be operating within specification. Adjacent components relevant to the fault were assessed. And the stove or oven was tested under actual operating conditions — a full preheat cycle on the oven, all burners tested on the stove — before the technician left.
That last step is not optional.
Why Gas Stove Burners Click After You've Already Turned Them Off
The persistent clicking of a gas stove igniter after the burner is already lit — or after the knob has been returned to off — is one of the most common stove complaints.
The first cause is usually moisture from spills or cleaning. The fix is often as simple as drying the area thoroughly. The second cause is a failed igniter switch, which requires replacement.
In Winter Park, Refrigerator Service Center carries igniter switches for all major gas stove brands and resolves this fault in a single visit.
Frequently Asked Questions
My oven runs but the temperature seems off. Is that calibration or a component fault?
It depends on the degree and consistency of the offset. A consistent 30-degree low reading is usually a thermostat sensor drift — repairable through calibration or sensor replacement. A variable or worsening offset may indicate a failing element or thermostat assembly.
Do you install wall ovens and freestanding ranges?
Yes. Both configurations are within our installation scope in Winter Park, including gas line confirmation, electrical verification, and anti-tip fitting.
My glass cooktop has a small crack. Can I still use it?
We assess whether the crack affects the subsurface elements and whether it creates a safety risk before advising either way.
How long does a typical stove or oven repair take?
Element replacements, igniter swaps, and sensor replacements typically take 45 minutes to an hour on-site. Control board faults requiring parts orders may need a follow-up visit within a few days.
Do you service Viking and Wolf ranges?
Yes. Both brands are within our scope and we work on them in Winter Park.
Winter Park Stove and Oven Reviews
"Gas range had two burners that wouldn't ignite at all... RSC tested each component, found one failed spark module and a moisture-compromised switch. Both fixed in one visit. The selective approach saved me from an unnecessary parts bill."
— Brian W., Winter Park
"Oven had been running about 35 degrees cool... Refrigerator Service Center tested with a reference thermometer, replaced the sensor, and verified correct temperature. Everything bakes evenly now."
— Donna C., Winter Park
"I was told by another service it was probably the control board... RSC found it was a failed bake element. Element replaced, tested through a full preheat. Far less than the control board quote."
— Paul M., Winter Park
Book Stove and Oven Repair in Winter Park, FL
Refrigerator Service Center brings the same diagnostic standard that defines its refrigeration work to every stove and oven job in Winter Park, FL. Book a visit and get a straight answer on what's wrong and what it takes to fix it.
Click Here to Call (888) 910-4766